編程單個SB8F
在對傳感器盒進行編程之前,機器人抓手公司,請確保有線輸入處于所需配置(開/關)以啟用輸出。按下AUTOSET按鈕并按住3秒鐘,直到READING紅燈開始閃爍,牡丹江機器人抓手,然后松開。紅燈(READING)閃爍表示微處理器正在讀取和存儲全部輸入的狀態。然后紅燈熄滅,啟用了輸出。黃燈(STORED)指示啟用輸出。
Before programming the sensor box, make sure that the wired inputs are in the confguration (ON/OFF) desired to enable the output. Press the AUTOSET button and hold it down for 3 seconds until the READING red light starts fashing, then release it.The red light (READING) fashing indicates that the microprocessor is reading and storing the state of all the inputs. Then the red light goes off and the output is enabled. Output enabling is indicated by the yellow light (STORED).
吸盤/聚氨酯
聚氨酯波紋管吸盤 VG.BP52
? 適用于zui低水平補償,機器人吸盤抓手,穩定性高
? 對瓦楞或多孔表面或非密封表面(例如紙板、塑料制品和不規則表面的復合材料)具有極i好的抓持力
? 也適用于提升力與表面平行的應用
? 具有非凡的彈性記憶功能
? 可提供 50 肖氏硬度,綠色
? 可提供 30/70 肖氏硬度。同時雙色吸盤既堅固又靈活
材料聚氨酯 PU
顏色 黃色 / 綠色
硬度 30/70
溫度范圍 10 - 45 °C
SBMS/SBMS-E - 從模塊
每個單獨的從模塊均可以連接單個傳感器。它由內部總線連接(由主模塊提供)供電,并觸發兩個固態繼電器的換向:基于傳感器輸出的常開觸點和常閉觸點。兩個選擇器可用于配置傳感器信號輸出(PNP/2線或NPN)和邏輯(正向或反向)。該模塊還有兩個用于診斷的LED指示燈。
Each individual slave module enables the connection of a singlesensor.
It is powered from the internal bus connection (provided by themaster module) and triggers the commutation of two solid staterelays: a NO contact and a NC contact based on sensor output.
Two selectors are available to conffgure sensor signal output(PNP/2 wires or NPN) and logic (direct or reverse).The module also has two LED indicators for diagnostics.
牡丹江機器人抓手-機器人吸盤抓手-吉瑪泰克(推薦商家)由吉瑪泰克自動化工程(常熟)有限公司提供。行路致遠,砥礪前行。吉瑪泰克自動化工程(常熟)有限公司致力成為與您共贏、共生、共同前行的戰略伙伴,更矢志成為氣動工具具有競爭力的企業,與您一起飛躍,共同成功!
本頁由吉瑪泰克自動化工程(常熟)有限公司通過合作平臺推送